Windows Says It Don't Have Read Permissions to My Linux Share

Skip to master content

• Article
• 01/28/2022
• 3 minutes to read

Is this page helpful?

Feedback volition be sent to Microsoft: By pressing the submit button, your feedback will be used to meliorate Microsoft products and services. Privacy policy.

In this article

Applies to: Windows 10

General troubleshooting

• Instead of File Explorer, access the shared folder past Command Prompt using the below command:

                    cyberspace apply <DeviceName>: \\<ServerName>\<ShareName>                                  

  Annotation

  For more than information, see Net utilize.

• Turn on the SMB 1.0 support feature from Control Panel by following these steps:

  1. Open Control Panel.

  2. Select Programs > Programs and Features > Turn Windows features on or off > SMB 1.0/CIFS File Sharing Support.

  3. Check SMB 1.0/CIFS Client, and and so press Enter.

     

• Plow on network discovery and file and printer sharing options by following these steps:

  1. Open up Command Console.

  2. Select Network and Cyberspace > Network and Sharing Center > Advanced sharing settings.

  3. Select Turn on network discovery.

  4. Select Turn on file and printer sharing nether Private.

  5. Select Salve changes.

     

• Ready the startup type of specified services to Automatic to make the computer visible on the network. Here's how to proceed:

  1. Become to Beginning.
  2. Go to Search, enter the word Services, and press Enter.
  3. Change the Startup type belongings to Automated for the following services.
     • Role Discovery Provider Host
     • Part Discovery Resources Publication
     • SSDP Discovery
     • UPnP Device Host
  4. Restart the system.

You may receive these fault letters:

You lot do not have permission to admission \\<IPAddress or Hostname>

Resolution

1. Hither's how to share permission to Everyone for the binder you want to share:

   1. Printing and hold (or correct-click) the shared folder.
   2. Select Properties, then select Advanced Sharing on the Sharing tab.
   3. Select Permissions, bank check Allow for Full Command of Everyone, and so press Enter.
   4. Select OK on the Advanced Sharing dialog box.

   

2. Here's how to allow the Full Command permission to Everyone:

   1. Select Edit on the Security tab.
   2. Select Add, enter Anybody in the Enter the object names to select field, and so press Enter.
   3. Check Allow for Full control of Everyone, and press Enter.
   4. Close the Properties dialog box.

   

3. Here'due south how to brand sure TCP/IP NetBIOS is enabled:

   1. Go to First.

   2. Go to Search, enter the word Services, and printing Enter.

   3. Double-click TCP/IP NetBIOS Helper on the right pane, and make certain the Startup type property is set to Automatic.

      

   4. Go to Control Panel > Network and Internet > Network and Sharing Center, select Change adapter settings on the left pane, then double-click Ethernet.

   5. Select Properties and double-click Internet Protocol Version 4 (TCP/IPv4) on the Networking tab.

   6. Select Avant-garde, select Enable NetBIOS over TCP/IP on the WINS tab, and then printing Enter.

   7. Select OK twice to close the dialog box.

      

Resolution

You lot can enable the guest access from your computer by using 1 of the following methods:

Method 1: Enable insecure guest logons with Registry Editor

1. Open Registry Editor.

2. Go to Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\LanmanWorkstation.

   Notation

   Yous must create the key if it doesn't be. Printing and hold (right-click) Windows, select New > Fundamental, and then name the fundamental LanmanWorkstation.

3. Printing and hold (correct-click) LanmanWorkstation, select New > DWORD (32-bit) Value, and then name it AllowInsecureGuestAuth. Double-click it, set the Value information to i, then printing Enter.

Method 2: Enable insecure guest logons with Local Group Policy Editor

1. Go to Start.

2. Go to Search, enter the word gpedit.msc, and then printing Enter.

3. Get toCalculator Configuration > Authoritative templates > Network > Lanman Workstation.

4. From the right-side pane, double-click Enable insecure invitee logons.

5. Select Enabled, and then press Enter.

   

Mistake code: 0x80004005. Unspecified error

Instead of obtaining an IP accost automatically, specify an IP address. Follow these instructions:

1. Select Utilize the following IP address if you want to specify the IP accost for the network adapter.
2. In the IP accost box, blazon the IP address that you want to assign to this network adapter. This IP address must be a unique accost in the range of addresses that are available for your network. Contact the network administrator to obtain a listing of valid IP addresses for your network.
3. In the Subnet mask box, type the subnet mask for your network.
4. In the Default gateway box, type the IP address of the computer or device on your network that connects your network to some other network or to the Net.
5. In the Preferred DNS server box, type the IP address of the computer that resolves host names to IP addresses.
6. In the Alternate DNS server box, type the IP address of the DNS reckoner that you want to use if the preferred DNS server becomes unavailable.
7. Select OK. In the Local Area Connexion Properties dialog box, select Shut.
8. In the Local Expanse Connection Condition dialog box, select Close.

slocumblethe1993.blogspot.com

Source: https://docs.microsoft.com/en-us/troubleshoot/windows-client/networking/cannot-access-shared-folder-file-explorer

Share this post